|
Hardware Requirements:
Compatible socketed obd1 ecu & laptop.
For more information visit http://www.ectune.com
We are an authorized dealer for eCtune. eCtune can only be bought from an authorized dealer.
Main Rom Features: - High and low cam tables with size 24x20
- High and low load vtec window(tps based)
- Secondary maps(second set of high / low cam maps)
- Electronic boost controller(gear or rpm dependent)
- RPM based compensation
- IAT based compensation
- Delta Map compensation(testing)
- Closeloop(testing)
- FastSpool option
- Adjustable Outputs(EGR/IAB/Purge(testing)/ACC(testing))
- Adjustable Hz
- Manual dual/tri/quad stage boost controller
- Cold, hot and MIL Stage boost cut protection
- 3-Step launch control with anti-lag and tps activation
- FTL Type
- TPS activation
- Fixed point
- FTL memory set by a button(rev to rpm press button, rev in memory until reset)/testing
- FTS Type:
- BurnOut:
- Press a button/switch to activate the burnout rev limit(testing)
- Rev Limiter with fuel cut/ ignition cut/ fuel and ignition cut :
- Hot and cold Rev
- Hot can use per gear limiter(if you want a lower rev limit in first gear) (testing)
- Soft Rev Limiter(Design phase)
- Gear depended shift light(MIL/check engine)
- 3 General purpose outputs with fuel/ignition adjustments(or ability to switch to secondary maps)
- Injector calibration with fuel offset, overall fuel trim and battery compensation table
- Fuel trims: injector, overall, o2, tps tip-in, crank, postfuel, iat.
- Gear based ignition and fuel corrections
- Target idle with IACV adjuster
- Closeloop(with use of wideband 0-5v signal)
- Target O2 maps in sofware for each fuel map
- Target O2 map in ecu(testing)
- Support of different kinds of mapsensors
- Table load selectable: map sensor/ tps sensor/ alpha-n
- Selectable gearbox
- User adjustable fuel cut settings
- Use any input for Service Check Connector or use KOEO TPS(key on engine off & tps>50%)
- Ac cut and ac idle recovery
- Disable Ignition correction above X mBar
- Starter signal disable
- Fuel pump control(disable/outputs/prime time)
- Alternator disable
- Control radiator fan with any output
- Ect overheat protection; limits rpm and throws code 6
Main Software Features:
- Datalogging:
- Fast datalogging of 80 parameters
- Live Tuner graphs( time vs AFR, rpm vs AFR/Boost)
- Save logs for later analyzing, view in Grap mode
- Export to CSV
- Custom Data display
- Warning range for most parameters
- Graph templates for different type analyzing
- Auto reconnect(search for ecu) on timeout
- Datalog files with Marker including comments. Usefull for later reply.
- Realtime Updating
- Fast updating of the rom
- Upload a calibration only(less then 1 seconds)
- Upload the base code(less then 4 seconds)
- Easy to use interface
- Lots of options and data still organized
- Basemap creator
- Selectable Ecu's
- Selectable Basemaps for different engines
- Adjust mapsensor during creation
- Adjust injectors during creation
- Select amount of columns, boost fuel, boost retard
- View and clear error codes
- Automatic software updates
- Table editing
- Easy table editing
- Auto Adjust selection based on wideband reading and target afr
- Interpolate Row and Columns
- Smooth Map or Smooth Selection
- Table Graphs
- 2d presentation of data
- 3d presentation of data
- Advance visual editing of tables
- Map
trails feature; You can see where the ecu read during a run, combined
with rpm vs Afr/Boost you have powerful tool(see help file)
- Tuner Graphs(Live plots)
- live Time vs AFR
- live rpm vs Afr/Boost
- rpm vs Accel(in development)
- Read or write chips
- eCtune uses universal calibrations which are rombase version independent
- Snapshot manager
- Make snapshots during tuning. Roll back an old calibration fast.
- Export/Import tables only
- 3 user configurable analog inputs
- 3 inputs for wideband logging
- Different predefined widebands or use custom volt to afr table
- Tools for Injector Calibration, Tps Calibration, Timing Sync, Boost Tables and Killing Injectors
- Auto detects all hardware connected. Never again you need to know what comm port is what
|
